Indoor Air Quality Products |
We offer the leading line of medium efficiency air filters.
Pleated panel filters were developed by Camfil with
the introduction of the Farr 30/30, the first air filter
product of its kind. The line has expanded over the years
and most recently was augmented by the introduction of the
For warranted longer-lasting
filters, the smart money is on Farr
30/30® filters. The Farr 30/30 has
an Energy Cost Index (ECI) of five stars, the
highest performance rating available.
Our exclusive media
is bonded to a welded wire grid and then
formed into a radial pleat, allowing full
use of the media. This configuration allows
the 30/30 filter to hold more dirt and last
longer. The 30/30 frame is made of water-resistant
beverage board instead of recycled cardboard,
so the 30/30 will stand up to the worst conditions
an HVAC system will present. No filter distortion
Available in standard and high
capacity models, it may be the model of choice where
air filters are changed on a PM (time) schedule. Consult
your local Camfil distributor for guidance in
this area. The Camfil Aeropleat is designed for
applications requiring competitive efficiency and dust
As a stand-alone filter, the Camfil
Farr Aeropleat addresses today's indoor air quality
concerns. Applications include commercial buildings,
educational facilities, medical facilities, industrial
manufacturing, and any other locations where a competitive
quality filter is required. As a prefilter, the Camfil
Farr Aeropleat offers protection and extended life
for higher efficiency final filters.
The Camfil Aeropleat IV® extended
surface pleated filter offers medium grade ASHRAE efficiency
for high capacity dirt loading applications. Incorporating
a mechanical particle capture principle, the Aeropleat
IV is a MERV 7 filter when evaluated per ASHRAE Standard
As a stand alone filter,
the Aeropleat IV will remove many of the contaminants
associated with today's indoor air quality concerns.
Available in 1", 2" and 4" depths,
its increased media area offers an extended service
life when compared to standard capacity pleated filters.
The Camfil AP-Eleven extended
surface pleated filter offers filtration for application
in units that have 1", 2" or 4" deep
tracks for filter installation. The AP-Eleven is a
MERV 11 filter when evaluated per ASHRAE Standard 52.2-1999.Using
the AP-Eleven may reduce the size of the HVAC system,
saving valuable mechanical area floor space. An Energy
Cost Index (ECI) of five stars is the highest performance
pleated filters remove nuisance dusts, lint and contaminants
associated with staining and are primarily designed
to protect equipment and act as prefilters. As a
stand alone filter, the AP-Eleven will perform these
tasks and also remove sub-micron particle, defined
as lung-damaging by cognizant authorities.
The Camfil AP-Thirteen extended surface pleated filter offers filtration for applications that have 2" or 4" deep filter tracks. The AP-Thirteen is a MERV 13 filter when evaluated per ASHRAE Standard 52.2 and meets the requirements for minimum filtration efficiency, as published in LEED manuals for new or existing buildings. The AP-Thirteen may reduce the size of the HVAC system, saving valuable mechanical area floor space. It also simplifies the upgrading of in-place systems, allowing existing units to meet LEED requirements without major equipment modification.
Camfil Type F/S air filters
are cleanable, low pressure drop, low or high velocity
permanent panel filters for applications with high
lint or large particle concentrations.
Camfil Type F/S Panel
filters are constructed of an electro-galvanized
steel media mesh, assembled into alternating layers
of corrugated and flat layers and enclosed in a 20-gauge
galvanized steel frame.
Camfil Type 44 are high-velocity
air filters for the elimination of oil and water mists.
They are cleanable, low pressure drop, permanent panels
for industrial and commercial applications.
When installed vertically,
the filter shall be 98% efficient on 20-micron size
contaminant when operating at a velocity of 500 fpm
face velocity. Initial resistance to airflow shall
not exceed 0.12".
The Camfil ECO® Moisture
Separator is highly effective in removing droplets,
water mist and fog from outside or recirculated
air. With an efficiency approaching 90% on 5-micron
droplets (98% on 20-micron size droplets) the ECO
offers excellent protection of HVAC components including
downstream filter banks.
In addition, the ECO may be used
downstream of DX or chilled water coils, and steam
or mist-type humidifiers to allow saturated air to
condense out of the airstream.